Centralvärme

Kommittébeteckning: SIS/TK 184 (Golvbeläggningar)
Källa: CEN
Svarsdatum: den 31 mar 2020
Se merSe mindre
 

This European Standard is applicable to water based surface embedded heating and cooling systems in residential, office and other buildings, the use of which corresponds to or is similar to that of residential buildings. This European Standard applies to heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. It also applies as appropriate to the use of other heating media instead of water.

Ämnesområden: Centralvärme
Kommittébeteckning: SIS/TK 184 (Golvbeläggningar)
Källa: CEN
Svarsdatum: den 31 mar 2020
Se merSe mindre
 

This European Standard specifies the boundary conditions and the prove methods for the determination of the thermal output of hot water floor heating systems as a function of the temperature difference between the heating medium and the room temperature. This standard shall be applied to commercial trade and practical engineering if proved and certifiable values of the thermal output shall be used. This European Standard applies to heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. This Part of this European Standard applies to hot water floor heating systems. Applying of Part 5 of this European Standard requires the prior use of this Part of this European Standard. Part 5 of this European Standard deals with the conversion of the thermal output of floor heating systems determined in Part 2 into the thermal output of heating surfaces embedded in walls and ceilings as well as into the thermal output of cooling surfaces embedded in floors, walls and ceilings. The thermal output is proved by a calculation method (Clause 6) and by a test method (Clause 9). The calculation method is applicable to systems corresponding to the definitions in EN 1264 1 (type A, type B, type C, type D). For systems not corresponding to these definitions, the test method shall be used. The calculation method and the test method are consistent with each other and provide correlating and adequate prove results. The prove results, expressed depending on further parameters, are the standard specific thermal output and the associated standard temperature difference between the heating medium and the room temperature as well as fields of characteristic curves showing the relationship between the specific thermal output and the temperature difference between the heating medium and the room.

Ämnesområden: Centralvärme
Kommittébeteckning: SIS/TK 184 (Golvbeläggningar)
Källa: CEN
Svarsdatum: den 31 mar 2020
Se merSe mindre
 

8. Scope This European Standard applies to heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. This document deals with the use in practical engineering of the results coming from part 2 and 5 and is applicable to floor-, ceiling- and wall heating systems, as well floor-, ceiling- and wall cooling systems. For heating systems, physiological limitations are taken into account when specifying the surface temperatures. In the case of floor heating systems the limitations are realised by a design based on the characteristic curves and limit curves determined in accordance with part 2 of this Standard. For cooling systems, only a limitation with respect to the dew point is taken into account. In predominating practice, this means that physiological limitations are included as well.

Ämnesområden: Centralvärme
Kommittébeteckning: SIS/TK 184 (Golvbeläggningar)
Källa: CEN
Svarsdatum: den 31 mar 2020
Se merSe mindre
 

This European Standard applies to heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. This document specifies uniform requirements for the design and the construction of heating and cooling floor, ceiling and wall structures to ensure that the heating/cooling systems are suited to the particular application. The requirements specified by this Standard apply only to the components of the heating/cooling systems which are part of the heating/cooling system. This document excludes all other elements which are not part of the heating/cooling system.

Ämnesområden: Centralvärme
Kommittébeteckning: SIS/TK 184 (Golvbeläggningar)
Källa: CEN
Svarsdatum: den 31 mar 2020
Se merSe mindre
 

This European Standard applies to water based heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. Part 5 of this standard deals with the recalculation of values determined in Part 2 of this European Standard for the system in question, using it for floor heating applications. The recalculation method described in this part of the standard enables the conversion of the calculation and test results of Part 2 into results for other surface orientations in the room, i. e. for ceiling and wall heating, as well as for the application as cooling surfaces, i. e. for floor, ceiling and wall cooling. It has to be emphasised that the test results of Part 2 of this European Standard are the basis of all calculation. Therefore the use of this prove method is necessary whether or not the system in question is used for heating or cooling application. This European Standard shall be applied to commercial trade and practical engineering if proved and certifiable values of the thermal output shall be used.

Kommittébeteckning: SIS/TK 189 (Innemiljö och energianvändning i byggnader)
Källa: CEN
Svarsdatum: den 31 mar 2020
Se merSe mindre
 

EN 1264 covers surface embedded heating and cooling systems installed in buildings, residential and non-residential (e.g. office, public, commercial and industrial buildings) and focuses on systems installed for the purpose of thermal comfort.

EN 1264 applies to water based heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. It also applies as appropriate to the use of other heating media instead of water.

EN 1264 applies to identify standardized product characteristics by calculation and testing the thermal output of heating for technical specifications and certification. For the design, construction and operation of these systems, EN ISO 11855 applies.

The systems covered in EN 1264 are adjoined to the structural base of the enclosure surfaces of the building, mounted directly or with fixing supports. It does not cover ceiling systems mounted in a suspended ceiling with a designed open air gap between the system and the building structure which allows the thermally induced circulation of the air. The thermal output of these systems can be determined according to ISO 18566, EN 14037 and EN 14240.

EN 1264-1 describes system types and characteristics of water based surface embedded radiant heating and cooling systems.

Ämnesområden: Centralvärme
Kommittébeteckning: SIS/TK 189 (Innemiljö och energianvändning i byggnader)
Källa: CEN
Svarsdatum: den 31 mar 2020
Se merSe mindre
 

This European Standard specifies the boundary conditions and the prove methods for the determination of the thermal output of hot water floor heating systems as a function of the temperature difference between the heating medium and the room temperature. This standard shall be applied to commercial trade and practical engineering if proved and certifiable values of the thermal output shall be used. This European Standard applies to heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. This Part of this European Standard applies to hot water floor heating systems. Applying of Part 5 of this European Standard requires the prior use of this Part of this European Standard. Part 5 of this European Standard deals with the conversion of the thermal output of floor heating systems determined in Part 2 into the thermal output of heating surfaces embedded in walls and ceilings as well as into the thermal output of cooling surfaces embedded in floors, walls and ceilings. The thermal output is proved by a calculation method (Clause 6) and by a test method (Clause 9). The calculation method is applicable to systems corresponding to the definitions in EN 1264 1 (type A, type B, type C, type D). For systems not corresponding to these definitions, the test method shall be used. The calculation method and the test method are consistent with each other and provide correlating and adequate prove results. The prove results, expressed depending on further parameters, are the standard specific thermal output and the associated standard temperature difference between the heating medium and the room temperature as well as fields of characteristic curves showing the relationship between the specific thermal output and the temperature difference between the heating medium and the room.

Ämnesområden: Centralvärme
Kommittébeteckning: SIS/TK 189 (Innemiljö och energianvändning i byggnader)
Källa: CEN
Svarsdatum: den 31 mar 2020
Se merSe mindre
 

EN 1264 covers surface embedded heating and cooling systems installed in buildings, residential and non-residential (e.g. office, public, commercial and industrial buildings) and focuses on systems installed for the purpose of thermal comfort.

EN 1264 applies to water based heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. It also applies as appropriate to the use of other heating media instead of water.

EN 1264 applies to identify standardized product characteristics by calculation and testing the thermal output of heating for technical specifications and certification. For the design, construction and operation of these systems, EN ISO 11855 applies.

The systems covered in EN 1264 are adjoined to the structural base of the enclosure surfaces of the building, mounted directly or with fixing supports. It does not cover ceiling systems mounted in a suspended ceiling with a designed open air gap between the system and the building structure which allows the thermally induced circulation of the air. The thermal output of these systems can be determined according to ISO 18566, EN 14037 and EN 14240.

EN 1264-3 deals with the use in practical engineering of the results coming from EN 1264-2 and EN 1264-5.

For heating systems, physiological limitations are taken into account when specifying the surface temperatures. In the case of floor heating systems the limitations are realized by a design based on the characteristic curves and limit curves determined in accordance with EN 1264-2.

For cooling systems, only a limitation with respect to the dew point is taken into account. In predominating practice, this means that physiological limitations are included as well.

Ämnesområden: Centralvärme
Kommittébeteckning: SIS/TK 189 (Innemiljö och energianvändning i byggnader)
Källa: CEN
Svarsdatum: den 31 mar 2020
Se merSe mindre
 

EN 1264 covers surface embedded heating and cooling systems installed in buildings, residential and non-residential (e.g. office, public, commercial and industrial buildings) and focuses on systems installed for the purpose of thermal comfort.

EN 1264 applies to water based heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. It also applies as appropriate to the use of other heating media instead of water.

EN 1264 applies to identify standardized product characteristics by calculation and testing the thermal output of heating for technical specifications and certification. For the design, construction and operation of these systems, EN ISO 11855 applies.

The systems covered in EN 1264 are adjoined to the structural base of the enclosure surfaces of the building, mounted directly or with fixing supports. It does not cover ceiling systems mounted in a suspended ceiling with a designed open air gap between the system and the building structure which allows the thermally induced circulation of the air. The thermal output of these systems can be determined according to ISO 18566, EN 14037 and EN 14240.

EN 1264-4 specifies uniform requirements for the design and the construction of heating and cooling floor, ceiling and wall structures to ensure that the heating/cooling systems are suited to the particular application.

The requirements specified by EN 1264 apply only to the components of the heating/cooling systems which are part of the heating/cooling system. EN 1264-4 does not cover all other elements which are not part of the heating/cooling system.

Ämnesområden: Centralvärme
Kommittébeteckning: SIS/TK 189 (Innemiljö och energianvändning i byggnader)
Källa: CEN
Svarsdatum: den 31 mar 2020
Se merSe mindre
 

EN 1264 covers surface embedded heating and cooling systems installed in buildings, residential and non-residential (e.g. office, public, commercial and industrial buildings) and focuses on systems installed for the purpose of thermal comfort.

EN 1264 applies to water based heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. It also applies as appropriate to the use of other heating media instead of water.

EN 1264 applies to identify standardized product characteristics by calculation and testing the thermal output of heating for technical specifications and certification. For the design, construction and operation of these systems, EN ISO 11855 applies.

The systems covered in EN 1264 are adjoined to the structural base of the enclosure surfaces of the building, mounted directly or with fixing supports. It does not cover ceiling systems mounted in a suspended ceiling with a designed open air gap between the system and the building structure which allows the thermally induced circulation of the air. The thermal output of these systems can be determined according to ISO 18566, EN 14037 and EN 14240.

EN 1264-5 deals with the recalculation of values determined in EN 1264-2 for the system in question. It enables the conversion of the calculation and measurement results of EN 1264-2 into results for other surface orientations in the room, i.e. for ceiling and wall heating, as well as for the application as cooling surfaces, i.e. for floor, ceiling and wall cooling. The test results of EN 1264-2 are the basis of all calculation, whether or not the system in question is used for heating or cooling application.