Rördelar av metall

Ämnesområden: Rördelar av metall
Kommittébeteckning: SIS/TK 132 (Koppar)
Källa: CEN
Svarsdatum: den 18 aug 2019
Se merSe mindre
 

This document specifies product characteristics, assessment methods, compliance criteria of the test results and a designation system for compression fittings for connecting with copper tubes. Compression fittings exist with sealing elements - metallic and/or non-metallic - called non manipulative (commonly referenced as type A) and without sealing elements, called manipulative (commonly referenced as type B). For the purposes of joining copper tubes, the fitting ends have a size range from 6 mm to 108 mm. The compression fittings are designed for a service lifetime up to fifty years.

The fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.

This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.

Compression fitting ends, Type A, are used with copper tubes to EN 1057 in all material hardness conditions.

Compression fittings, Type A, will possibly require an internal support when used with R220 (annealed) copper tube and the manufacturer’s advice should be sought.

Compression fitting ends, Type B, are used with R220 (annealed) or R250 (half-hard) copper tube to EN 1057.

Compression fittings, Type B, may be used with R290 (hard) copper tube and the manufacturer’s advice should be sought.

Adaptor fittings for use with copper tubes may combine compression ends with fitting ends defined in the other parts of EN 1254.

Compression fittings for use with copper tubes may also have flanged end connections according to EN 1092-3.

Compression fittings for use with copper tubes may also have a plated or other decorative surface coating.

Fittings can be produced by machining, metal forming, casting, or fabrication.

Products covered by this standard are intended to be used in:

a) liquid applications:

— hot, cold or combined hot and cold water systems according to EN 806;

— closed heating systems according to EN 12828 and cooling systems;

— drainage systems;

— sprinkler systems according to EN 12845.

b) gas applications:

— natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;

— compressed air systems.

Ämnesområden: Rördelar av metall
Kommittébeteckning: SIS/TK 132 (Koppar)
Källa: CEN
Svarsdatum: den 18 aug 2019
Se merSe mindre
 

This document specifies product characteristics, assessment methods, compliance criteria of test results and a designation system for fittings with compression ends for use with plastic and multilayer pipes which are defined in the applicable pipe standard. For the purposes of joining plastics pipes, the fitting ends have a size range from 10 mm to 160 mm. The fittings are designed for a service lifetime up to fifty years.

The compression fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.

This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.

Adaptor fittings for use with plastic and multilayer pipes may combine compression ends with fitting ends defined in the other parts of EN 1254.

Compression fittings for use with plastic and multilayer pipes may also have flanged end connections according to EN 1092-3.

Compression fittings for use with plastic and multilayer pipes may also have a plated or other decorative surface coating.

Fittings can be produced by machining, metal forming, casting, or fabrication.

Products covered by this standard are intended to be used in:

a) liquid applications:

— Hot, cold or combined hot and cold water systems according to EN 806;

— closed heating systems according to EN 12828 and cooling systems;

— drainage systems;

— sprinkler systems according to EN 12845.

b) gas applications (not valid for multilayer pipes):

— natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;

— compressed air systems

Ämnesområden: Rördelar av metall
Kommittébeteckning: SIS/TK 132 (Koppar)
Källa: CEN
Svarsdatum: den 18 aug 2019
Se merSe mindre
 

This document specifies product characteristics, assessment methods, compliance criteria of the test results and a designation system for fittings with ends for capillary soldering or capillary brazing for connecting with copper tubes e.g. EN 1057, EN 13348, EN 13349, EN 12735-1, EN 12735-2 etc. For the purposes of joining copper tubes, the fitting ends have a size range from 6 mm to 108 mm. These fitting ends exist in three forms: end feed fittings and integral solder and integral brazing ring fitting ends. The fittings are designed for a service lifetime up to fifty years.

The fittings are used up to the operating temperatures and corresponding maximum operating pressures as indicated in Annex A.

This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.

The capillary fittings for soldering or brazing to copper tubes are used with solder alloys in accordance with alloys specified in EN ISO 9453 and brazing alloys in accordance with alloys specified in EN ISO 17672.

Adaptor fittings for use with copper tubes may combine capillary soldering or capillary brazing ends with fitting ends defined in the other parts of EN 1254.

Capillary fittings for soldering or brazing may also have flanged end connections according to EN 1092-3.

Capillary fittings for soldering or brazing may also have a plated or other decorative surface coating.

Fittings can be produced by machining, metal forming, casting or fabrication.

Products covered by this standard are intended to be used in:

a) liquid applications:

— hot, cold or combined hot and cold water systems according to EN 806;

— closed heating systems according to EN 12828 and cooling systems;

— drainage systems;

— sprinkler systems according to EN 12845;

— refrigeration systems;

b) gas applications:

— natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;

— compressed air systems;

— medical gas systems according to EN ISO 7396;

— refrigeration systems.

 

Ämnesområden: Rördelar av metall
Kommittébeteckning: SIS/TK 132 (Koppar)
Källa: CEN
Svarsdatum: den 18 aug 2019
Se merSe mindre
 

This document specifies product characteristics, assessment methods, compliance criteria and a designation system for threaded fittings. These threaded ends exist with metallic and with non-metallic sealing elements for the purposes of joining with tubes, pipes, fittings or valves, the threaded ends have a size range from 3,175 mm (1/8") to 101,6 mm (4"). The threaded fittings are designed for a service lifetime up to fifty years.

The fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.

This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.

Threaded fittings may also have flanged end connections according to EN 1092-3.

Threaded fittings may also have a plated or other decorative surface coating.

Fittings can be produced by machining, metal forming, casting, or fabrication.

Products covered by this document are intended to be used in:

a) liquid applications:

— hot, cold or combined hot and cold water systems according to EN 806;

— closed heating systems according to EN 12828 and cooling systems;

— drainage systems;

— sprinkler systems according to EN 12845.

b) gas applications:

— natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;

— compressed air systems.

Ämnesområden: Rördelar av metall
Kommittébeteckning: SIS/TK 132 (Koppar)
Källa: CEN
Svarsdatum: den 18 aug 2019
Se merSe mindre
 

This document specifies product characteristics, assessment methods, compliance criteria and a designation system for capillary fittings with short ends for brazing to copper tubes e.g. EN 1057, EN 13348, EN 13349, EN 12735-1, EN 12735-2, etc. These fitting ends exist in two forms: end feed fittings and integral brazing ring fittings. For the purposes of joining copper tubes, the fitting ends have a size range from 14,7 mm to 159 mm. The fittings are designed for a service lifetime up to fifty years.

The fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.

This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.

The capillary fittings with short ends for brazing to copper tubes are used with brazing alloys in accordance with alloys specified in EN ISO 17672.

Not all copper alloys that can be used to manufacture fittings can be brazed and those that can be brazed may require different brazing techniques (guidance is provided in in prEN1254–20:2019, Annex A).

Fittings with short ends for capillary brazing may also have threaded end connections. These threaded ends exist with metallic and with non-metallic sealing elements. For the purposes of joining with tubes, pipes, fittings or valves, the threaded ends have a size range from 1/8" to 4".

Adaptor fittings for use with copper tubes may combine short ends for capillary brazing with fitting ends defined in the other parts of EN 1254.

Capillary fittings with short ends for brazing may also have flanged end connections according to EN 1092-3.

Fittings can be produced by machining, metal forming, casting, or fabrication.

Products covered by this standard are intended to be used in:

a) liquid applications:

— hot, cold or combined hot and cold water systems according to EN 806;

— closed heating systems according to EN 12828 and cooling systems;

— drainage systems;

— sprinkler systems according to EN 12845;

— refrigeration systems.

b) gas applications:

— natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;

— compressed air systems;

— medical gas systems according to EN ISO 7396;

— refrigeration systems.

Ämnesområden: Rördelar av metall
Kommittébeteckning: SIS/TK 132 (Koppar)
Källa: CEN
Svarsdatum: den 18 aug 2019
Se merSe mindre
 

This document specifies product characteristics, assessment methods, compliance criteria and a designation system for push-fit fittings for the purpose of joining tubes of copper, plated copper, multilayer pipes and plastics pipes. The fitting ends have a size range from 6 mm to 54 mm. The fittings are designed for a service lifetime up to fifty years.

This document is applicable to push-fit fittings for joining one or more of the following tubes or pipes:

— copper tubes to EN 1057; copper composite according to UNI 11342, plastic and multilayer pipes covered by EN 15015.

The fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.

This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.

Adaptor fittings may combine push-fit ends with fitting ends defined in the other parts of EN 1254.

Push-fit fittings for metallic tubes may also have flanged end connections according to EN 1092-3.

Push-fit fittings may also have a plated or other decorative surface coating.

Fittings can be produced by machining, metal forming, casting, or fabrication.

Products covered by this standard are intended to be used in liquid applications:

— hot, cold or combined hot and cold water systems according to EN 806;

— closed heating systems according to EN 12828 and cooling systems;

— drainage systems;

— sprinkler systems according to EN 12845.

Ämnesområden: Rördelar av metall
Kommittébeteckning: SIS/TK 132 (Koppar)
Källa: CEN
Svarsdatum: den 18 aug 2019
Se merSe mindre
 

This document specifies product characteristics, assessment methods, compliance criteria and a designation system for press fittings including their elastomeric seals, for connecting with metallic tubes. The fitting ends have a size range from 6 mm to 108 mm. The press fittings are designed for a service lifetime up to fifty years.

This document is applicable to press fittings for joining one or more of the following tubes:

— copper tubes to EN 1057 and

— stainless steel tubes to EN 10312

with wall thicknesses and tempers as specified by the manufacturer.

The fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.

Press fittings are used with tubes with wall thicknesses greater than or equal to the wall thickness given in Annex B, to ensure that tubes can withstand the radial pressing forces involved.

This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.

Adaptor fittings for use with copper tubes may combine press ends with fitting ends defined in the other parts of EN 1254.

Press fittings for use with metallic tubes may also have flanged end connections according to EN 1092-3.

Press fittings for use with metallic tubes may also have a plated or other decorative surface coating.

Fittings can be produced by machining, metal forming, casting, or fabrication.

Products covered by this standard are intended to be used in:

a) liquid applications:

— hot or cold or combined hot and cold water systems according to EN 806;

— closed heating systems according to EN 12828 and cooling systems;

— drainage systems;

— sprinkler systems according to EN 12845.

b) gas applications:

— natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;

— compressed air systems.

.

Ämnesområden: Rördelar av metall
Kommittébeteckning: SIS/TK 132 (Koppar)
Källa: CEN
Svarsdatum: den 18 aug 2019
Se merSe mindre
 

This document specifies product characteristics, assessment methods, compliance criteria and a designation system for fittings with radial and axial press ends for use with plastics and multilayer pipes. The fitting ends have a size range from 10 mm to 160 mm. The fittings are designed for a service lifetime up to fifty.

This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.

Adaptor fittings for use with plastic and multilayer pipes may combine press ends with fitting ends defined in the other parts of EN 1254.

Press fittings for use with plastic and multilayer pipes may also have flanged end connections according to EN 1092-3.

Press fittings for use with plastic and multilayer pipes may also have a plated or other decorative surface coating.

Fittings can be produced by machining, metal forming, casting, or fabrication.

Products covered by this standard are intended to be used in:

a) liquid applications:

— hot, cold or combined hot and cold water systems according to EN 806;

— closed heating systems according to EN 12828 and cooling systems;

— drainage systems;

— sprinkler systems according to EN 12845;

b) gas applications:

— natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;

— compressed air systems.

Ämnesområden: Rördelar av metall
Kommittébeteckning: SIS/TK 132 (Koppar)
Källa: CEN
Svarsdatum: den 18 aug 2019
Se merSe mindre
 

This document contains definitions, thread dimension, reference data (minimum bore), supporting information (assembling instructions) and describes the test methods referenced by other parts of the EN 1254 series.

Thread dimensions comprise: wall thickness at threaded portions of fittings, dimensions of tail pipe ends for swivel fittings, dimensions of gas union connectors, thread dimensions and thread profile.

Test methods comprise: leak tightness under internal hydrostatic pressure, leak tightness under internal pneumatic pressure, resistance of joints to static flexural strength, resistance to pull out of joints, leak tightness of joints under vacuum, the resistance of joints to temperature cycling, resistance of joints with metallic tube to vibration, integrity of fabricated fitting bodies or having an 'as cast' microstructure, resistance to stress corrosion, detection of a carbon film on the surface of copper fittings, determination of mean depth of dezincification, resistance of joints to pressure cycling, disconnection and re-use, determining if the diameter and/or the length of engagement of a capillary end is/are within the specified tolerance, determining the minimum length of engagement of an integral solder or brazing ring socket having a formed groove.