Detaljer om förslaget

Svensk titel: Plaströrsystem - Plaströr för avlopp (låg och hög temperatur) inomhus - Polyetylen (PE) - Del 1: Specifikationer för rör, rördelar och systemet
Nummer:prEN 1519-1
Källa:CEN
Kommitté:SIS/TK 226
Namn på kommittén:Plaströrssystem
Publicerat:den 14 nov 2017
Sista svarsdatum:den 16 jan 2018
Contact email:kommentera(at)sis.se
Förslagets omfattning:

This European Standard specifies the requirements for solid-wall polyethylene (PE) pipes with smooth internal and external surfaces extruded from the same compound/formulation throughout the wall, fittings and the system for:

— soil and waste discharge applications (low and high temperature) inside buildings (application area code "B");

— soil and waste discharge applications (low and high temperature) for both inside buildings and buried in the ground within the building structure (application area code "BD").

NOTE 1 The intended use is reflected in the marking of products by "B" or "BD.

NOTE 2 For use buried in the ground within the building structure are intended only those components marked with "BD", with a nominal ring stiffness of at least SN4 for dimensions equal to or greater than 75 mm.

This European Standard is also applicable to PE pipes and fittings and the system intended for the following purposes:

— ventilating part of the pipework in association with discharge applications;

— rainwater pipework within the building structure.

It also specifies the test parameters for the test methods referred to in this standard.

This European Standard covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.

NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes, e.g. CEN/TR 13801 [1].

NOTE 4 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 16.

It applies to pipes and fittings, marked with "B", which are intended to be used inside buildings and outside buildings fixed onto the wall.

It applies to pipes and fittings, marked with "BD", which are intended to be used for both inside buildings and buried in the ground within the building structure.

This standard is applicable to PE pipes and fittings of the following types:

— plain-ended;

— with integral elastomeric ring seal socket;

— for butt fusion joints;

— for electrofusion joints;

— for mechanical joints

where the fittings can be manufactured by injection-moulding or can be fabricated from pipes and/or mouldings.

NOTE 5 EN 476[2] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements.

NOTE 6 For information about the chemical resistance of PE, guidance is given in ISO/TR 10358[3] and for rubber materials in ISO 7620[4].

Detta dokument föreslås att fastställas och publiceras som svensk standard.

För att lämna allmänna kommentarer på standardförslaget i sin helhet och på föreslagen titel – klicka på förslagets titel i innehållsförteckningen till vänster.

För att lämna specifika kommentarer på innehållet – skriv kommentaren och föreslagen ändring i rutan under avsnittet i fråga.

Standardförslag på engelska föreslås att fastställas som svensk standard utan översättning. Kommentarer på engelskspråkiga standardförslag bör vara på engelska.

För att ett standardförslag ska kunna fastställas som svensk standard måste det vara förenligt med svensk lagstiftning. Det är således viktigt att berörda svenska myndigheter klarlägger ifall standardförslaget är förenligt med svensk lagstiftning.